Water Well Drilling Cost Per Foot in Massachusetts (2026): $32-$72/ft

When Massachusetts drillers quote you a price, it almost always comes down to a per-foot rate. Understanding what that rate includes — and why it ranges from $32 to $72 per foot — is the single most important thing you can do before signing a contract. This guide breaks down per-foot drilling costs across Massachusetts so you can evaluate quotes with confidence.

For a full overview of Massachusetts well costs, see our complete Massachusetts well drilling cost guide.

Massachusetts Per-Foot Cost at a Glance

Cost Factor	Massachusetts 2026
Per-foot range	$32–$72
Average per-foot rate	$50
Typical residential depth	270 ft (range: 80–600 ft)
Primary aquifer	Fractured Crystalline Bedrock Aquifers / Cape Cod Glacial Outwash Aquifer
Water table depth	15-50 feet on Cape Cod; 80-300 feet in bedrock areas of central and western Massachusetts
Best drilling season	April through November

What’s Included in Massachusetts Per-Foot Pricing

Most Massachusetts drillers include the following in their quoted per-foot rate:

• Drilling labor and equipment mobilization — getting the rig to your property and the actual drilling operation
• Drill bit wear and fuel — consumables used during boring
• Basic borehole logging — recording depth, geology, and water-bearing zones
• Drilling fluid — mud rotary or air rotary medium for flushing cuttings

What’s Typically NOT Included

These items are typically quoted separately:

• Well casing — PVC or steel pipe lining the borehole ($8–$25 per foot)
• Well screen — slotted section at the water-bearing zone ($10–$20 per foot)
• Grout and seal — cement seal preventing surface contamination ($3–$8 per foot)
• Pump and pressure system — submersible pump, pressure tank, wiring ($2,500–$6,000)
• Electrical hookup — wiring from well to home electrical panel ($1,000–$3,000)
• Water testing — bacteria, mineral, and chemical analysis ($150–$500)
• Permit fees — varies in Massachusetts (Local Boards of Health issue well permits under Massachusetts Department of Environmental Protection (MassDEP) regulations) — typically $50–$500

Always ask for an itemized quote to see exactly what your per-foot rate covers.

Casing Cost Per Foot in Massachusetts

Casing is one of the biggest cost variables beyond the drilling itself:

Casing Type	Cost Per Foot	Best For	Lifespan
Schedule 40 PVC (4”)	$8–$12	Shallow wells, sandy/sedimentary formations	30–50 years
Schedule 80 PVC (4”)	$10–$16	Standard residential, moderate depths	40–60 years
Steel (4”)	$15–$25	Deep wells, hard rock formations	50+ years
Steel (6”)	$20–$35	High-flow residential, light irrigation	50+ years

In areas of Massachusetts with hard bedrock or deeper wells (typically the upper end of the 80–600 ft range), steel casing is often required because PVC can crack at depth. In sandy/sedimentary regions and shallower wells, PVC handles the load.

How Depth Affects Per-Foot Rates in Massachusetts

Per-foot rates often increase with depth — even within Massachusetts:

0–200 feet: The most straightforward drilling. Standard rigs handle these depths easily; formations are usually softer. Rates stay at the $32–$50 range.

200–400 feet: Rates typically increase $5–$10 per foot above the base rate. Harder formations may be encountered, drilling takes longer per foot, more casing is required.

400–600 feet: Specialized equipment may be needed. Drill bit changes are more frequent and the risk of problematic formations increases. Add $10–$20 per foot above base rate.

600+ feet: Heavy-duty rigs, steel casing, and significantly more time. Rates can reach the upper end of Massachusetts’s range ($72/ft) or beyond. Massachusetts’s deepest wells are typically in the 500–600+ ft range.

Many Massachusetts drillers quote a base per-foot rate for the first 200–300 feet, then a higher rate for additional depth. Make sure your quote specifies the rate structure for different depth tiers.

Why Per-Foot Costs Vary in Massachusetts

Massachusetts bedrock is primarily crystalline igneous and metamorphic rock — granite, gneiss, and schist — that requires wells to intersect water-bearing fractures. Cape Cod and the Islands rest on glacial outwash sand and gravel, providing productive shallow wells.

The geology summarized above is the primary driver of per-foot cost variation within Massachusetts. Areas with softer sedimentary formations drill faster and cheaper. Areas with limestone, granite, or volcanic rock require slower, more expensive methods. Massachusetts’s primary aquifer — the Fractured Crystalline Bedrock Aquifers / Cape Cod Glacial Outwash Aquifer — sits at 15-50 feet on Cape Cod; 80-300 feet in bedrock areas of central and western Massachusetts, which directly affects how deep your well must go.

Total Well Cost Estimates in Massachusetts

Here’s what Massachusetts property owners actually pay when you combine per-foot drilling, casing, pump, and all other costs:

Well Depth	Drilling Only	Complete System (with pump, casing, electrical)
80 ft (shallow)	$2,560–$5,760	$5,060–$10,760
270 ft (typical)	$8,640–$19,440	$11,140–$24,440
500 ft (deeper)	$16,000–$36,000	$18,500–$41,000
600 ft (deepest typical)	$19,200–$43,200	$21,700–$48,200

How to Compare Per-Foot Quotes

When you receive quotes from multiple Massachusetts drillers:

1. Confirm what’s included. A $40/ft quote that includes casing is cheaper than a $30/ft quote where casing is extra.
2. Ask about depth tiers. Will the rate increase after 200 or 300 feet?
3. Get a not-to-exceed estimate. Good drillers cap the total cost based on expected depth in your area.
4. Check for mobilization fees. Some drillers charge $500–$2,000 to move the rig, especially for rural locations.
5. Verify licensing. Massachusetts requires water well drillers to hold a permit from MassDEP.

We recommend getting at least three quotes. Request free quotes from licensed Massachusetts drillers to compare pricing in your area.

When to Drill in Massachusetts

April through November; deep frost and rocky ground make winter drilling difficult and expensive

Driller schedules typically fill 4–8 weeks in advance, especially in peak drilling season. Off-season drilling (where weather allows) sometimes captures 5–15% labor savings.

Frequently Asked Questions

How much does it cost to drill a water well per foot in Massachusetts?

Massachusetts well drilling costs $32–$72 per foot in 2026, with $50 per foot as the average. Total cost depends on depth — a typical 270-foot well costs $8,640–$19,440 for drilling alone, plus $2,500–$5,000 for pump and connection.

Why is well drilling cost per foot different across Massachusetts?

Massachusetts’s geology varies regionally — softer sedimentary formations drill faster and cheaper than hard limestone, granite, or volcanic bedrock. Wells targeting deeper aquifers also cost more per foot because of additional drill bit wear, slower progress, and the need for steel rather than PVC casing.

Does the per-foot rate include the well casing?

Usually not. Most Massachusetts drillers quote drilling and casing separately. PVC casing adds $8–$16 per foot; steel casing adds $15–$35 per foot. Always ask for an itemized breakdown so you know exactly what the per-foot rate covers.

How deep do you have to drill for water in Massachusetts?

In Massachusetts, residential well depths typically range from 80 to 600 feet, with 270 feet being the average. Your specific depth depends on local geology, target aquifer, and how productive nearby wells have been. The Fractured Crystalline Bedrock Aquifers / Cape Cod Glacial Outwash Aquifer is Massachusetts’s primary residential aquifer, sitting at 15-50 feet on Cape Cod; 80-300 feet in bedrock areas of central and western Massachusetts.

Is it cheaper to drill a shallow well in Massachusetts?

Yes — both the per-foot rate and total cost are lower for shallow wells. A 80-foot well costs $2,560–$5,760 for drilling, while a 600-foot well runs $19,200–$43,200. However, you can’t choose your well depth — it depends on where the productive aquifers are beneath your property.

Do Massachusetts well drillers charge a flat rate or per-foot rate?

Most Massachusetts residential well drillers quote per-foot rates, though some offer flat-rate packages where well depth is predictable. Per-foot pricing is more common because depth can vary even between neighboring properties. Some drillers quote a base rate for the first 200–300 feet and a higher rate for additional depth.

How can I get the best per-foot rate on well drilling in Massachusetts?

Get at least three quotes from licensed drillers, drill during the slower season (april through november is peak; outside that window can save 5–15%), and choose a property access point that minimizes mobilization costs. Request free quotes here to compare rates from drillers in your area.

Next Steps

Understanding per-foot pricing is just one piece of the puzzle. Explore our other Massachusetts well drilling resources:

• Massachusetts Well Drilling Cost Guide — complete overview of costs in Massachusetts
• Well Drilling Cost Per Foot (National) — compare Massachusetts to other states
• How Much Does It Cost to Drill a Well — full national breakdown
• Well Pump Costs — pump, pressure tank, and electrical pricing
• Massachusetts Contractor Directory — find licensed drillers in Massachusetts